Address No. 65, Shahid Ghandi St., North Sohrevardi Ave., Tehran, Iran

Phone +98 21 87754

E-Mail Address info@abadgarangroup.com

Abadgaran Group Office
Address End of West 6th St., Safadasht Industrial Zone, Safadasht, Malard Road, Karaj, Iran

Phone +98 21 65741911-5

Abadgaran Group Factory
Thank you for giving us the opportunity to serve you better. Please help us by taking a few minutes to tell us about the service that you have received so far.

E.M.P10

 

Two component Epoxy Top Coat Cured with Polyamine

DESCRIPTION

A two component, high performance, solvent free epoxy topcoat cured with polyamine. It cures to a hard, tough and well adhering protective coating.

 

SURFACE PREPARATION

Prior to paint application all surfaces should be assessed and treated in accordance with ISO 8504:1992. Oil or grease should be removed in accordance with SSPC-SP1 solvent cleaning. Concrete should be cured for a minimum of 28 days prior to coating. The moisture content of the concrete should be below 5%. All surfaces to be coated should be clean, dry and free from curing compounds, release agents, trowelling compounds, surface hardeners, efflorescence, grease, oil, dirt, old coatings and loose or disintegrating concrete. All poured and precast concrete must also blasted, wire brushed or acid etched to remove laitance. Spalled concrete should be repaired by cutting out to sound concrete and patching with ABADUR-P1. Cracks, holes and honeycombs must be repaired prior to application. Surface preparation shall not take place in the following conditions: 1) At temperature below 10 º C 2) When the relative humidity greater than 85% 3) When the surface temperature is less than 3 º C above the dew point 4) Outside day light hours on exterior locations The blasted and cleaned surface may advantageously be sealed with ABAPRIME-11.

  • Good resistance against penetration of water and chemicals
  •  Excellent adhesion
  •  Good mechanical strengths
  • Excellent immersion and non-immersion service in sea water, salt solutions and corrosive conditions

 

E.M.P10 may be applied by airless spray, brush or roller. Like all high performance coating, this product must be applied as recommended to obtain the maximum protection for which this coating is formulated.

The exothermic nature of epoxy setting reactions may cause rapid temperature rise when the mixture is left massed in a bucket, resulting in high temperatures and loss of utility of the product. To maximize handling and working time, pour the mixture into shallow pans and start application as soon as possible. 
  • Do not dilute the mixture
  • Paint shall not be applied when wind speed is in excess of  7 m/s                                       
  • Do not apply this coating when  surface temperature is below 12ºC.
In hot climate, material temperature should be 20 to 25 ºC prior to mixing; otherwise pot life becomes 
 
 
FIELD OF APPLICATION
  • Offshore platforms
  •  Piping in chemical plants
  •  Lining of tanks

 

  • Appearance: Viscous liquid.
  • Mixing Ratio: 100:8 (by weight).
  • Density (A+B): Approx. 1.3 g/cm3.
  • Volume solid: 100%.
  • Theoretical spreading rate at 250 micron:  4 m²/l.
  • Typical dry film thickness: 200-300 μm.
  • Amount required (g/m2): 250-400.
  • Application method: Airless spray , brush or roller.
  • Adhesion to Concrete: > 2 MPa (Concrete failure) According to ASTM D 4541.

 

MIXING
Open containers Component B and add entire contents to Component A. Mix thoroughly with an electric stirrer, taking care to entrain as little air as possible. Always mix such amount that shall be just sufficient to be used up within 20 minutes. 
 
PACKAGING
20 kgs set.
 
STORAGE & SHELFLIFE
The shelf life is 12 months if unopened, stored free from frost, moisture and direct sunlight.
 
TECHNICAL SERVICE
The Abadgaran International Technical Service Department is available to assist you in the correct use of our products and its resources are at your disposal entirely without obligation.

 

  • This product is Flammable. Keep away from heat and open flame .Keep container closed .Use with adequate ventilation. Avoid prolonged and repeated contact with skin. If used in confined areas, observe the following precautions to prevent hazards of fire or explosion or damage to the health:
  1. Circulate adequate fresh air continuously during application and drying.
  2. Use fresh air masks and explosion proof equipment.
  3. Prohibit all flames, sparks, welding and smoking. 
  • MSDS is available from Abadgaran.

 

Expect Something Extra