Address No. 65, Shahid Ghandi St., North Sohrevardi Ave., Tehran, Iran

Phone +98 21 87754

E-Mail Address info@abadgarangroup.com

Abadgaran Group Office
Address End of West 6th St., Safadasht Industrial Zone, Safadasht, Malard Road, Karaj, Iran

Phone +98 21 65741911-5

Abadgaran Group Factory
Thank you for giving us the opportunity to serve you better. Please help us by taking a few minutes to tell us about the service that you have received so far.
phone
instagram
telegram
aparat

POWER PLAST–ES

DESCRIPTION

POWER PLAST-ES is high range water-reducer and super plasticizing admixture based on modified polycarboxylic (PC) polymers. It acts efficiently to give controlled workability about 105 minutes. POWER PLAST-ES can develop the early compressive strength of concrete.

It is controlled based on ASTM C1017/C1017 M, ASTM C494/C494 M TYPE F, EN 934-2 and ISIRI 2930 Table 3& 4

POWER PLAST–ES

Applications

Pre-cast concrete Concreting in thin and congested steel reinforcement sections  Concrete slip forming  Underwater concreting by using Tremie concrete Concreting where workability retention is beneficial Produces  High Performance Concrete (HPC)  Produces High Strength Concrete (HSC) Produces Self-Consolidating Concrete (SCC) Produces Water Resistant Concrete (WRC) & Produces Preplaced Aggregate Concrete (PAC) Exposed concretes Dosage The optimum dosage of POWER PLAST-ES can be determined by trials in the site. Depending on concrete mix design (sizes and types of aggregates, cement content, water/cement ratio, ambient temperature and concreting conditions), a dosage of between 0.3 and 0.9 percent by weight of cement or cementitious material is recommended.

For use with other range of dosage, contact ABADGARAN Technical Services Department.

Directions of Use

  1. POWER PLAST-ES could be added to a part of concrete mixing water then added to the concrete mix
  2. POWER PLAST-ES could be added to the concrete mix during the mixing cycle at the same time as the water or the aggregate or it could be added to ready-mix concrete before placing concrete
  3. Admixtures must be weighed carefully Features and Benefits  Reducing the potential for AAR (Alkali-Aggregate Reaction), due to reduction of cement contents and concrete permeability  Enables economies in mix designs to be achieved and reducing depreciation of concreting Equipments Significant reduction in crack propagation resulting from creep and shrinkage potential of concrete  Providing great compressive strength of concrete, because of a lower water/cement ratio without increasing the amount of cement

  • Reduces cement content in concrete.
  • Design of concrete mixes with water-cement ratios in the range of 0.28 to 0.4.
  • Increases workability.
  • Prevents bleeding and segregation of concrete.
  • No needs for vibrators .
  • Improves concrete consistency .
  • Eliminates air content of concrete.
  • possible to reduce the time of de-moulding (approximately 8 to 12 hours) .
  • Achieve to early compressive strength of concrete in all ages.
  • It can be used with all types of Portland cement including Sulphate Resisting.
  • Use simultaneously with silica fume, fly ash and other pozzolanic materials .
  • Increased adhesion between concrete and steel.
  • Considerably reduces permeability.
  • Increases the durability of concrete against climatic effects.

  • Pre-cast concrete.
  • Concreting in thin and congested steel reinforcement sections.
  • Concrete slip forming.
  • Underwater concreting by using Tremie concrete .
  • Concreting where workability retention is beneficial Produces.
  • High Performance Concrete (HPC).
  • Produces High Strength Concrete (HSC).
  • Produces Self-Consolidating Concrete (SCC) .
  • Produces Water Resistant Concrete (WRC).
  • Produces Preplaced Aggregate Concrete (PAC).
  • Exposed concretes.

Chemical base

 modified polycarboxylic (PC) polymers

Specific gravity

 1.08+ 0.05 g/cm3

Physical state

 liquid

Chloride content

 Nil to BS 5075 

  • Shelf life: 1 year in the original package.
  • Storage condition: should be protected from direct sunlight and frost. Keep container in the temperature range between +10°C and +30°C .
  • Packing: 22 kg container or 1000 kg tank.

HEALTH AND SAFETY
This product does not contain any substances hazardous to human health and the environment. However, it should not be swallowed and allowed to be in contact with skin and eyes. In case of contact with eyes rinse immediately with plenty of water.
POWER PLAST–ES is not flammable. For further information refer to the material safety data sheet. MSDS is available at ABADGARAN website.
 
 
WE DEVELOP CHEMISTRY