Address No. 65, Shahid Ghandi St., North Sohrevardi Ave., Tehran, Iran

Phone +98 21 87754

E-Mail Address info@abadgarangroup.com

Abadgaran Group Office
Address End of West 6th St., Safadasht Industrial Zone, Safadasht, Malard Road, Karaj, Iran

Phone +98 21 65741911-5

Abadgaran Group Factory
Thank you for giving us the opportunity to serve you better. Please help us by taking a few minutes to tell us about the service that you have received so far.

ABAINJECT EPW-210

TWO COMPONENTS, SOLVENT FREE INJECTION ADHESIVE

ABAINJECT EPW-210 is a two-components, solvent-free injection adhesive specially formulated based on high strength modified epoxy resin and special hardeners. This product is designed in low, medium and high viscosity ranges to allow injection in different parts of cracks. This product is able to be used in grouting of either wet, dry and water-filled cracks to result in a filled cracks and fully restored concrete. It conforms to ASTM C881 and EN 1504-5.

SUBSTRATE PREPARATION

Substrates must be sound, clean, free from oil and grease, old coatings, surface treatments, etc. Concrete, mortar and stone should be thoroughly prepared by mechanical means such as grinding, chiseling, etc. Cracks must be cleaned to remove dust by using compressed air.

In case of Inaccessible cracks, use ETCHING SOLUTION twice for 15 minutes. After each time, rinse thoroughly with water for 15 minutes.

 

EXTENSION OF USAGE

Depending on the Geometrical Scale of Section to be Injected, the appropriate amount and type of products should be considered.

         

APPLICATION

ABAINJECT EPW-210 is supplied in two containers as a unit. Always mix a complete unit in the proportion supplied. Once the unit has been mixed it must be used within the working Pot life specified.

1-Agitate Part A and B separately with a power agitator.

2-Combine entire contents of curing agent (part B) with base (part A) and mix thoroughly with power agitator.

3-Mix thoroughly for at least three minutes, scraping the container bottom and side to assure complete mixing. There is no induction or waiting time required after mixing before injection.

 

Mixed ABAINJECT EPW-210 can be injected under pressure into the cracks using a single component injection pump, or a high pressure hand pump. Injection ports (packers) are set at appropriate intervals next to the crack and the crack between the injection ports (packers) sealed with ABADUR-MP to prevent injection resin to escape during the injection process. Vertical cracks should always be injected from the bottom upwards. As soon as injection resin oozes out of the next packer/injection port, the first one is sealed and the injection process continued from the next one. After completion of the injection process, the injection ports (packers) as well as the sealing material between the ports are removed.

 

  • Excellent bond to wet, water filled and dry concrete.
  • Different viscosity ranges for excellent penetration into existing cracks.
  • Injectable by a single component either manual or automated pumps.
  • Solvent free.
  • Resistant to wide range of chemicals.

  • Pressure injection of cracks in structural concrete and masonry.
  • Able to be injected in any condition of cracks in process of structural repairs.
  • Seals concrete from water absorption, chloride-ion intrusion and chemical attack.
  • Prolongs life of cracked concrete.

TECHNICAL PROPERTIES

Appearance

 

ABAINJECT EPW-210L    Part A: Yellow viscose liquid

                                            Part B: Brownish viscose liquid

ABAINJECT EPW-210M   Part A: Green viscose liquid

                                            Part B: Brownish viscose liquid

ABAINJECT EPW-210H   Part A: Blue viscose liquid

                                               Part B: Brownish viscose liquid

 

Mixing Ratio (A:B)

 

 

 ABAINJECT EPW-210L     100:40

 ABAINJECT EPW-210M     100:30

 ABAINJECT EPW-210H     100:20

 

Density (A+B)

 

ABAINJECT EPW-210L      1.4 g/cm3

ABAINJECT EPW-210M     1.6 g/cm3

ABAINJECT EPW-210H      1.8 g/cm3

 

Volume solid

100%

Cleaner

MACHINERY CLEANER

 
 

PERFORMANCE CHARACTERISTICS

Complies with the scope of standard EN 1504-5

 

Conditioning

Method of standard

Strength (MPa)

category

Water filled

EN 12618-2

>2.5

F1

Wet

>2.5

F1

Damp

>2.5

F1

Dry

>2.5

F1

 

 

 

 

 

 

 

 

 

 

Pot Life

40°C

25°C

15°C

Temperature

20 Minutes

30 Minutes

50 Minutes

Pot Life

 

 

 

STORAGE

  • Shelf life: 1 year in the original package.
  • Storage condition: should be protected from direct sunlight and moisture. Keep gallons in the temperature range between +10°C and +30°C.
  • Packing: Pre-batched Part A+B:
  1.     ABAINJECT EPW-210L 14 kg
  2.     ABAINJECT EPW-210M 15.6 kg
  3.     ABAINJECT EPW-210H 15 kg
     

HEALTH AND SAFETY
For information and advice on the safe handling, storage and disposal of chemical products, users
shall refer to the most recent Material Safety Data Sheet (available on request) containing physical, ecological, toxicological and other safety-related data.

 

WE DEVELOP CHEMISTRY