Address No. 65, Shahid Ghandi St., North Sohrevardi Ave., Tehran, Iran

Phone +98 21 87754

E-Mail Address info@abadgarangroup.com

Abadgaran Group Office
Address End of West 6th St., Safadasht Industrial Zone, Safadasht, Malard Road, Karaj, Iran

Phone +98 21 65741911-5

Abadgaran Group Factory
Thank you for giving us the opportunity to serve you better. Please help us by taking a few minutes to tell us about the service that you have received so far.
phone
instagram
telegram
aparat

MS-5-FP

PC and PP Fiber Modified Silica Fume Gel

MS-5-FP improves the rheological properties of concrete. It is based on a highly pozzolanic mineral admixture that reduces water absorption and increases the compressive strength and makes concrete impermeable. Workability retention is special properties of MS-5-FP. High range water reduction is one of the most exceptional properties of MS-5-FP.

MS-5-FP comprises the following chemicals:

  1. Silica fume.
  2. New generation super plasticizer based on modified polycarboxylic (PC) polymers.
  3. PP Fiber.

This advanced-technology product can be controlled using the following standards:

ASTM C1202

BS EN 12390-8, BS 1881-122

DOSAGE
The optimum dosage of MS-5-FP can be determined by trials in the site. Depending on concrete mix
design (concrete type, workability, compressive strength, sizes and types of aggregates, cement content,
water/cement ratio, ambient temperature and concreting conditions), a dosage of between 2.0 and 10.0 percent by weight of cement is recommended.
For use with other range of dosage, contact ABADGARAN Technical Services Department.
Note: please contact our engineering office in case of simultaneously use of more than one admixture.

DIRECTION OF USE
MS-5-FP can be added to concrete in two ways:

  • MS-5-FP could be added to ready-mix concrete before placing concrete.
  • MS-5-FP could be added to a part or whole of concrete mixing water then added to the concrete mix.
     

ADVANTAGES

  • Significantly reduces water-cement ratio.
  • Reduces cement content in concrete.
  • Increases workability and workability retention of concrete.
  • Increases flexural, tensile and compressive strength of concrete.
  • Achieve to early compressive strength of concrete.
  • Improves pumpability of concrete and reduces damages to concreting equipment.
  • Improves concrete consistency.
  • Enables economies in mix designs to be achieved when special conditions such as chemicals attack, dynamic load, etc.
  • Considerably reduces permeability.
  • Increases durability of concrete.
  • Increases the abrasion resistance of concrete.
  • Reduce the risk of cracks in concrete.
  • It makes it possible to produce concrete with w/c ratio below 0.35.

APPLICATION

  • Produces High Strength Concrete (HSC) in special conditions (high dynamic loads).
  • Produces non-osmosis concrete for the regions exposed to chemicals attack.
  • Reinforced and non-reinforced concrete.
  • Dams, water and wastewater treatment, bridges, channels, etc.
  • Hot weather concreting.
     

Physical state

Slurry

Specific gravity

1.39 ± 0.05 g/cm3

Color

Grey

  • Shelf life: 1 year in the original package.
  • Storage condition: should be protected from direct sunlight and frost. Keep pail in the temperature range between +10°C and +30°C.
  • Packing: 24 kg pail.

HEALTH AND SAFETY
This product does not contain any substances hazardous to human health and the environment. However,it should not be swallowed and contact with skin and eyes.
 In case of contact with eyes, rinse immediately with plenty of water. MS-5-P is not flammable. For further information refer to the material safety data sheet.

MSDS is available at ABADGARAN website.
 

WE DEVELOP CHEMISTRY