Address No. 65, Shahid Ghandi St., North Sohrevardi Ave., Tehran, Iran

Phone +98 21 87754

E-Mail Address info[At]

Abadgaran Group Office
Address End of West 6th St., Safadasht Industrial Zone, Safadasht, Malard Road, Karaj, Iran

Phone +98 21 65741911-5

Abadgaran Group Factory
Thank you for giving us the opportunity to serve you better. Please help us by taking a few minutes to tell us about the service that you have received so far.



A three-component pourable, moisture tolerant, epoxy grout based on a high grade epoxy resin and specially graded aggregates. On mixing, a flowable grout is produced for use in heavy engineering and difficult conditions.


 Before mixing ensure all the components are cool, shaded and dry. If not preconditioned store all components below 25° C for 24 hours before using. The temperature of grout, baseplate and foundation are more important than the air temperature because they are directly related to the flow of grout. Add component A & B in a mixing vessel and mix under slow speed (RPM 400) for approximate 1 minute. Then add component C and continue mixing until a flowing uniform grout is achieved. Avoid excessive mixing which will result in reduction of working time and heat generation.

Ready-to-mix, pre-batched units
Chemical resistant
Solvent free
Rapid shrinkage free hardening
High mechanical strength
Good impact and vibration resistance
Good bonding to most substrates




Under-grouting and bedding of base plates, bridge bearings, machine bases, seat base-plates for
light and heavy machinery including heavy impact and vibratory machinery, reciprocating engines, compressors, pumps, presses, etc.
Crane tracks
While grouting the base plates ensure there is sufficient pressure head to maintain movement of grout.
Base plates with a flat base pour the grout from one side through the other across the short dimensions.
Ensure entrapped air can escape when grouting closed areas.
Where grout cannot flow and have smooth movement because of the length of pour pushing aids like steel chains, strips of plywood, etc. can be used.
The base plate with anchor bolts, dowel, starter bar, etc. should be grouted first followed by the base plate.
If grouting in multiple layers, it is necessary to sprinkle a small amount of 2.5 mm aggregate over the first layer before the grout reaches its setting time. Before placement of 2nd layer brush out loose aggregates from the 1st pour. Another method is to
scrabble gently the top surface and make it rough when grout reaches near to its setting time.





MixingRatio(A:B:C):  5:2.5:22.5(byweight)
Density(A+B+C):  Approx.2.0g/cm³.

 Minimumgroutdepth: 10mm.
 Maximumgroutdepth: 120mm.               
(AccordingtoASTMC579):  Curingtime  +23°C
                        1days           ~85 MPa
                        3days           ~90 MPa
                        7days           ~100 MPa

(AccordingtoASTMC580):     ~30MPa

(AccordingtoASTMC307):     ~14Mpa

Bondstrength:              >3MPa(Concretefailure)
Creep:                        ~4.0MPa(600psi/31500N)
(AccordingtoASTMC1181):    ~2.5MPa(400psi/21000N)

(AccordingtoASTMC531)      <0.05%

ThermalExpansion           ~2.0×10-5mm/mm/c
Coefficient                -30C - +30C
(AccordingtoASTMC531)      ~3.5×10-5mm/mm/c
                           +24C - +100C

Waterabsorption            ~0.05%(7days)

Thermalstability(HDT)      +50C

(AccordingtoASTMD695)     ~20GPa(compressive)
(AccordingtoEN53452)      ~15GPa(Flexural)

(AccordingtoASTMD638)     ~1.5%

(AccordingtoASTMD638)     0.1±0.05



Concrete should be old enough, if it is newly placed concrete then it needs to be 21-28 days old and to have reached its design strength.
Concrete should have attained a minimum compressive strength of 21 MPa, higher strength concrete is recommended for optimum performance of grout.
All surfaces should be dry, clean, and free from standing water, grease, curing compounds, mold oils, all loosely adhered aggregates and cement particles, etc.
Chip the concrete surface so aggregates are exposed to ensure all laitance and weak particles are removed. Alternatively use a spray on surface retarder when placing concrete. The exposed aggregate amplitude should not be greater than
10-15 mm.
Chamfer the edges of the concrete 45 degrees to
50 mm. width to avoid sharp corners which helps to reduce the potential for cracking.
Shade the foundation from direct sunlight for at least 24 hours before grouting and 48 hours after grouting.




This product is Flammable. Keep away from heat and open flame .Keep container closed .Use with adequate ventilation. Avoid prolonged and repeated contact with skin. If used in confined areas, observe the following precautions to prevent hazards of fire or explosion or damage to the health:
1.Circulate adequate fresh air continuously during application and drying.
2.Use fresh air masks and explosion proof equipment.
3.Prohibit all flames, sparks, welding and smoking. MSDS is available at ABADGARAN website.
The ABADGARAN INTERNATIONAL GROUP Technical Department is available to assist you in the correct use of our products and its resources are at your disposal entirely without obligation.




Expect Something Extra