Address No. 65, Shahid Ghandi St., North Sohrevardi Ave., Tehran, Iran

Phone +98 21 87754

E-Mail Address info[At]

Abadgaran Group Office
Address End of West 6th St., Safadasht Industrial Zone, Safadasht, Malard Road, Karaj, Iran

Phone +98 21 65741911-5

Abadgaran Group Factory
Thank you for giving us the opportunity to serve you better. Please help us by taking a few minutes to tell us about the service that you have received so far.



ABADUR-P1is a two component 100 percent solids content, solvent-free epoxy based smooth floor topcoat.Its excellent wear, abrasion and chemical resistance properties make it suitable for the protection of primed concrete floors in the food industry, industrial and commercial warehouses, power plants and other locations where a heavy duty, smooth and cleanable floor topcoat is required. .


All surfaces to be coated should be clean, dry and free from contamination .Prior to paint application all surfaces should be assessed and treated in accordance with ISO 8504:1992. Oil or grease should be removed in accordance with SSPC-SP1 solvent cleaning Primed surfaces ABADUR-P1can be applied over approved primers. The primer surface should be dry and free from all contamination, and ABADUR-P1must be applied within the overcoating intervals specified. Concrete Surfaces Concrete should be cured for a minimum of 28 days prior to coating. The moisture content of the concrete should be below 5% .All surfaces should be clean and dry All Cracks in the concrete shall be filled by ABADUR-P1, before applying topcoat. Surface preparation shall not take place in following conditions: -At temperature below 5 º C. -When the relative humidity greater than 50-60%. -When the surface temperature is less than 3 º C above dew the point. - Outside day light hours on exterior locations

  • ABADUR-P1 resists splash and spillage of a wide range of industrial chemicals and cleaning agents. It can easily clean from dirt and grease, resisting normal cleaning procedures.
  • Material is supplied in two containers as a unit. Always mix a complete unit in the proportion supplied. Once the unit has been mixed it must be used within the working Pot life specified.
  • Agitate part A with a power agitator.
  • Combined entire contents of curing agent (part B) with base (part A) and mix thoroughly with power agitator.
  • Product is also available in pre-measured units, eliminating the need for field measuring of components. Mix thoroughly for at least three minutes, scraping the container bottom and side to assure complete mixing. There is no induction or waiting time required after mixing before application.
  • The exothermic nature of epoxy setting reactions may cause rapid temperature rise when the mixture is left massed in a bucket, resulting in high temperatures and loss of utility of the product .To maximize handling and working time, pour the mixture into shallow pans or dump and squeegee tile mixture out onto surface to be coated within a few minutes of mixing
  • Like all high performance coating, this product must be applied as recommended to obtain the maximum protection for which this coating is formulated.
  • Pour ABADUR-P1on the floor and spread using a flat trowel, after 10 minutes roll the surface with a pin roller to remove air bubbles.
  • Apply a minimum of 1.5 mm ABADUR-P1normally provides a smooth, high gloss finish after application.
  • In hot climate, material temperature should be 20 to 25 º C prior to mixingotherwise pot life becomes very short.
  • Do not thin for any reason
  • Paint shall not be applied when wind speed is in excess of 7 m/s
  • Do not apply this coating when surface temperature is below 12º C.

Color: Grey

Mixing Ratio: 3:1(by weight)

Density (A+B): Approx. 1.8 g/cm3

Volume solid: 100%

Substrate: Primed concrete

Flash point: 80°C

Cleaner: T-200


10kgs set.
The shelflife is 12 months if unopened, stored free from frost, moisture and direct sunlight.
The Abadgaran International Technical Service Departmentis available to assist you in the correct use of our productsand its resources are at your disposal entirely withoutobligation.

This product is Flammable. Keep away from heat and open flame .Keep container closed .Use with adequate ventilation. Avoid prolonged and repeated contact with skin. If used in confined areas, observe the following precautions to prevent hazards of fire or explosion or damage to the health:
1-Circulate adequate fresh air continuously during application and drying.
2-Use fresh air masks and explosion proof equipment.
3- Prohibit all flames, sparks, welding and smoking.
MSDS is available from Abadgaran.

Expect Something Extra