Address No. 65, Shahid Ghandi St., North Sohrevardi Ave., Tehran, Iran

Phone +98 21 87754

E-Mail Address info@abadgarangroup.com

Abadgaran Group Office
Address End of West 6th St., Safadasht Industrial Zone, Safadasht, Malard Road, Karaj, Iran

Phone +98 21 65741911-5

Abadgaran Group Factory
Thank you for giving us the opportunity to serve you better. Please help us by taking a few minutes to tell us about the service that you have received so far.

ABAREPAIR-ECO

SPECIAL POLYMER MODIFIED CONCRETE REPAIR MORTAR
DESCRIPTION

ABAREPAIR-ECO is a ready-mix and non-shrink cement base dry powder provides smooth level
surfaces with highly consistent repair mortar for special purpose concrete and masonry repairs.
Due to high quality adhesives formulated in ABAREPAIR-ECO, it has an excellent adhesion to most common substrates.

It meets the requirements of the following standards:
EN 1504-3

SURFACE PREPARATION
Surfaces should be clean sound and free from oil, grease, laitance and loose particles.
 Metal surfaces should also be clean and free of rust, oil, grease and contaminants.
The concrete should be presaturated for preferably 6 hours with water before application.


MIXING
ABAREPAIR-ECO is simply mixed with water to yield a stiff easily workable compound with shrinkage compensating properties.
The quantity of water depends on the desired consistency but as a guide, it is recommended to
add the entire contents of the bag into the pre-measured (4.5-5.5 liters approximately) water while mixing.
Mix with a paddle mixer or trowel to ensure a homogenous lump free material is achieved. 
Do not try to remix the product after losing workability by the addition of more water.

APPLICATION
1. Remove damaged concrete and prepare exposed steel reinforcement.
2. Thoroughly clean repair area using high pressure water jet to remove all loose debris and contamination.
3. Replace damaged concrete using ABAREPAIR-ECO, build up in layers if necessary.
Apply ABAREPAIR-ECO with a trowel or spatula. Press hard by hand. Thicker repairs
may be achieved by working in layers.


DOSAGE
The optimum dosage of ABAREPAIR-ECO to meet specific requirement depending on porosity
and rough substrate, the normal dosage range is from 1.5 to 1.8 kg/m2/mm thickness of layer.


CURING
Keep repaired areas damp, with spraying water at least 24 hours.

 

ADVANTAGES

  • Excellent adhesion to most common substrates.
  • Non-shrinkage.
  • High mechanical strengths.
  • Early stiffening and hardening time.
  • Provides maximum protection against freeze and thaw cycles.
  • Improves impermeability of concrete.
  • No destructive effect on the steel.
  • Available in wide range of colors.
  • Easy to use.
     

FIELD OF APPLICATION

  • Repairing of cracks and porous surfaces.
  • Provides smooth level surfaces.
  • Underlayment for floors and walls before placement of new covering materials.
  • Filling voids and holes.
  • Can be used for surfaces that are in direct contact with water.
  • Suitable for hydraulic structures.
  • Applying fillet in water tanks, etc.
     

Physical state

 Powder

Color

Gray

Fresh mortar density

 ~1.6 g/cm³

Chloride ion

 No chloride content

Pot life

20 minutes @ +25°C

STORAGE

  • Shelf life: 1 year in the original package.
  • Storage condition: Should be protected from direct sunlight and moisture. Keep bag in the temperature range between +10°C and +30°C.
  • Packing: 25 kg bag.

HEALTH AND SAFETY
This product does not contain any substances hazardous to human health and the environment.
However, it should not be swallowed and contact with skin and eyes. In case of contact with eyes,
rinse immediately with plenty of water. Gloves & goggles should be worn when applying. 
For further information refer to the material safety data sheet.
ABAREPAIR-ECO is not flammable. MSDS is available at ABADGARAN website.

WE DEVELOP CHEMISTRY