Address No. 65, Shahid Ghandi St., North Sohrevardi Ave., Tehran, Iran

Phone +98 21 87754

E-Mail Address info@abadgarangroup.com

Abadgaran Group Office
Address End of West 6th St., Safadasht Industrial Zone, Safadasht, Malard Road, Karaj, Iran

Phone +98 21 65741911-5

Abadgaran Group Factory
Thank you for giving us the opportunity to serve you better. Please help us by taking a few minutes to tell us about the service that you have received so far.

ABATOP-FSL

FAST SETTING SELF LEVELING CEMENT BASED UNDERLAYMENT
ABATOP-FSL is a polymer modified single component cementitious Fast Setting self-leveling compound.
ABATOP-FSL has been designed for leveling, smoothing and repairing interior and exterior concrete and engineer-approved floors prior to installing floor coverings.
ABATOP-FSL has high strength and is abrasion-resistant, able to withstand light foot traffic after 2 to 3 hours and vehicular rubber-wheel traffic after 3 days.

SUBSTRATE PREPARATION
Ensure the concrete substrate is clean and free from oil, grease, sealers, curing compounds,paints, polymer coatings, dust or other foreign (bond breaking) matter.
Excess bitumen,adhesive or laitance should be removed by light scabbling or mechanical captive shot blasting or grinding, followed by vacuuming to remove debris and dust.
Depending on different conditions, new concrete floors must be 7 to 28 days old.
The substrates should be presaturated for preferably 6 hours with water before application.


MIXING
ABATOP-FSL requires 6.0 - 6.25 liters of water per 25 kg bag and is best mixed with a forced action, high shear stirrer, or by a heavy duty electric mixing drill at approx. 600 R.P.M.
Add pre measured water to a clean mixing bucket. Gradually add ABATOP-FSL into the water whilstcontinuously mixing the contents of the bucket. 
When the entire contents of the bag have been added to the water, mix for a further two minutes to produce a smooth homogenous consistency. 
Do NOT mix by hand. Do NOT add excess water. Discard any ABATOP-FSL that has hardened or stiffened in the mixing bucket. 
Too intensive agitation of the mixture may result in unwanted air inclusion.
Before application, one should allow the mixture to stand for a short time. 
Further addition of water will NOT reconstitute a useable mixture.


APPLICATION
The mixed material is poured onto the prepared substrates and spread with a smooth edge trowel to the required thickness in one operation. 
Alternatively the use of a spiked roller will ensure a smooth even finish that will not require any further attention prior to the floor coverings being applied.


CURING
It necessary to cure areas of ABATOP-FSL with humidified method for at least 24 hours.

 

ADVANTAGES

  • Excellent flowing properties and filling ability.
  • Good self-leveling properties.
  • Good adhesion to most common substrates.
  • Reinstating large areas in relative short time periods.
  • Resistant to furniture castors.
  • Very fast application.
  • Dimensionally stable.
  • Non shrinkage.
  • Reinstating large areas in relative short time periods.
  • Very fast application.
  • Dimensionally stable.
  • Single component product, just add water.
  • Installation can be carried out in a single application.
  • Rapid curing.
  • Can be applied directly onto prepared concrete surfaces.
  • Eliminates the need for sand and cement screeds.
  • May create more ceiling height by removal of screed.
  • Reduces load in building when replaces screed.
  • Easy apply.
     

FIELD OF APPLICATION

  • Underlayment for floor coverings such as carpet, ceramic tiles, vinyl, parquetry, linoleum etc.
  • Fast repairs of uneven concrete floors.
  • Residential, commercial and medium industrial application.
  • Application thickness from feather edge to 10 mm in a single application.
  • New construction and refurbishment projects.
  • Flat smooth surfaces over existing concrete slabs.
  • Leveling existing uneven concrete floors.

 

Physical state

 Powder

Color

 Gray

Water/Powder

 0.24 to 0.25

Specific gravity of fresh mortar

 2.00±0.05 g/cm³

Chloride ion

 No chloride content.

Pot life

 20 minutes @ +25°C

STORAGE

  • Shelf life: 1 year in the original package.
  • Storage condition: should be protected from direct sunlight and moisture. Keep bag in the temperature range between +10°C and +30°C.
  • Packing: 25 kg bag.

HEALTH AND SAFETY
This product does not contain any substances hazardous to human health and the environment.
However, it should not be swallowed and allowed to be in contact with skin and eyes. 
In case of contact with eyes rinse immediately with plenty of water. When applying gloves & goggles should be worn. 
For further information refer to the material safety data sheet.
ABATOP-SL is not flammable.


MSDS is available at ABADGARAN website.
 

WE DEVELOP CHEMISTRY