Address No. 65, Shahid Ghandi St., North Sohrevardi Ave., Tehran, Iran

Phone +98 21 87754

E-Mail Address info[At]abadgarangroup.com

Abadgaran Group Office
Address End of West 6th St., Safadasht Industrial Zone, Safadasht, Malard Road, Karaj, Iran

Phone +98 21 65741911-5

Abadgaran Group Factory
Thank you for giving us the opportunity to serve you better. Please help us by taking a few minutes to tell us about the service that you have received so far.

E.M.K.S

DESCRIPTION

A two component solvent-free, heavy-duty mortar on the basis of epoxy resins and modified polyamine hardeners. E.M.K.S displays excellent corrosion and chemical resistance for tank lining, immersion and non-immersion service with just a single coat. The fully cured mortar possesses a very high compressive strength and a high resistance to abrasion.

Concrete should be cured for a minimum of 28 days prior to coating. The moisture content of the concrete should be below 5%. All surfaces should be clean, dry and free from curing compounds, release agents, trowelling compounds, surface hardeners, efflorescence, grease, oil, dirt, old coatings and loose or disintegrating concrete. All poured and precast concrete must also blasted, wire brushed or acid etched to remove laitance. Spalled concrete should be repaired by cutting out to sound concrete and patching with ABADUR-P1. Cracks, holes and honeycombs must be repaired prior to application.

  • Solvent-free
  • Excellent chemical resistance against a wide range of alkalies, inorganic acids, salts, solvents, oil and other corrosive materials.
  • Excellent abrasion resistance
  • Excellent adhesion
  • Superior mechanical strengths
  • Cures without shrinkage

 

  • The material is applied using a plastering trowel in a maximum layer thickness of 4 mm in one work step. The application can carried out in multiple layers.
  • In hot climate, material temperature should be 20 to 25 º C prior to mixingotherwise pot life becomes very short.
  •  Anti-acid tiling 
  •  Anti-acid tile grouting 
  • Sealing horizontal and vertical surfaces which are exposed to increased chemical stresses and for heavy duty corrosion protection.
  • Battery rooms
  •  Food and dairy plants 
  •  Electrolysis tanks

 

Appearance: Black thixotropic paste
Mixing Ratio: 1:1 (by weight)
Density (A+B): Approx. 1.7 g/cm3
Volume solid: 100%
Amount required (kg/m2): 4-5
Application method: Trowel
Adhesion to Concrete: >2 MPa (Concrete failure) According to ASTM D 4541
Touch dry: 6 hrs
Recoating: 24 hrs
Full cure: 7 days

 

MIXING
Open containers Component B and add entire contents to Component A. Mix thoroughly with an electric stirrer, taking care to entrain as little air as possible. Always mix such amount that shall be just sufficient to be used up within 30 minutes. Do not dilute the mixture.
PACKAGING
10 kgs set.
Part A paste 5 kg plastic pailsPart B paste 5 kg plastic pails.
STORAGE &SHELFLIFE
The shelf life is 12 months if unopened, stored free from frost, moisture and direct sunlight.
TECHNICAL SERVICE
The Abadgaran International Technical Service Department is available to assist you in the correct use of our products and its resources are at your disposal entirely without obligation.

 

  • This product is Flammable. Keep away from heat and open flame .Keep container closed .Use with adequate ventilation. Avoid prolonged and repeated contact with skin. If used in confined areas, observe the following precautions to prevent hazards of fire or explosion or damage to the health:
  • 1-Circulate adequate fresh air continuously during application and drying.
  • 2-Use fresh air masks and explosion proof equipment.
  • 3- Prohibit all flames, sparks, welding and smoking.
  • MSDS is available from Abadgaran.

 

Expect Something Extra